done repair unknow baseband n imei null

From : Asangsm Dongle

Atf error and solution

Here : atf-error-solution

how to repair boot E15i with setool box

 q:
my semc 8x55-based smartphone can't be detected by PC or detecting as "QHUSB_DLOAD".
my semc 7227-based smartphone can't be detected by PC.
my semc 8250-based smartphone can't be detected by PC.


a:
at least semc boot damaged

step I.

for 8x55-based phones select USB as interface, then

1. pda tab, select corresponding phone model
2. options tab, check : signed mode, alternative security bypass
3. pda tab, press "recovery"

for 7227,8250-based phones select COM as interface, then

1. pda tab, select corresponding phone model
2. options tab, check : signed mode, alternative security bypass, use testpoint ("GND" type)
3. pda tab, press "recovery"

 if you get next output

Code:

MINOR ERROR [ MISC_CLASS: MISC_ERROR, TA_invalid,_format_may_be_required ]
MINOR ERROR [ MISC_CLASS: MISC_ERROR, TA_invalid,_format_may_be_required ]

and do not have trim area backup, thats bad, but you still can fix phone : check Next post
step II.

1. pda tab, select corresponding model
2. options tab, check : signed mode
3. pda tab, add needed firmware files ( DO NOT UNPACK ) ( BOTH APP and FSP) to fw area
4. press "flash"

q:
during second stage of testpoint unlock procedure i made testpoint wrong/disconnect phone/etc - my phone dead, but i have security units backup.


a:
that can be fixed easy enough.

step I.

for 8x55-based phones select USB as interface, then

1. pda tab, select corresponding phone model
2. options tab, check : signed mode, alternative security bypass
3. pda tab, press "recovery"

for 7227,8250-based phones select COM as interface, then

1. pda tab, select corresponding phone model
2. options tab, check : signed mode, alternative security bypass, use testpoint ("GND" type)
3. pda tab, press "recovery"

if you will get output like

Code:

MINOR ERROR [ MISC_CLASS: MISC_ERROR, TA_invalid,_format_may_be_required ]
MINOR ERROR [ MISC_CLASS: MISC_ERROR, TA_invalid,_format_may_be_required ]

then and only then perform next step, otherwise skip to step IV
step II.

1. pda tab, select corresponding model
2. options tab, check : signed mode, alternative security bypass, format gdfs during write

for 7227,8250-based phones select COM as interface and
2. options tab, check : signed mode, alternative security bypass, use testpoint ("GND" type), format gdfs during write

3. pda tab, select trim area package files for your phone model ( DO NOT UNPACK, DO NOT UNZIP, DO NOT TOUCH IT IN ANY WAY ) in misc. edit
4. press "write gdfs"

step III.

1. pda tab, select corresponding model
2. options tab, check : signed mode, alternative security bypass

for 7227,8250-based phones select COM as interface and
2. options tab, check : signed mode, alternative security bypass, use testpoint ("GND" type), format gdfs during write

3. pda tab, select YOUR BACKUP SCRIPT
4. press "write script"

step IV.

1. pda tab, select corresponding model
2. options tab, check : signed mode
3. pda tab, add needed firmware files ( DO NOT UNPACK ) ( BOTH APP and FSP) to fw area
4. press "flash" 

CHina PA 6231 Jumper 100% tested

How to Unlock bootloader for HTC

How to Repair "EFS" SGH-I9100 Samsung Galaxy SII with Riff box

1-Select "Speed"
2-Select "I9100" Model
3-Set "Start Address" "Data Length"

Start Address : "0x0000 0040 0000"
Lentgh : "0X0000 0140 0000"

4-Uncheck 3 option...Select "Rom1"
5-Open "I9100_EFS.bin" in "Main" Window
6-Select "Use Adress as Offset xxxxxx"
7-Press "write"

Second Method : (Write efs From Dump file)

Quote:

* Please Note : Dump Size Does not matter....So,User Can Use Any Size,More Than 128MB...
It's Means,You can use 128MB,256MB,512MB,1GB,----16GB
1-Select "Speed"
2-Select "I9100" Model
3-Set "Start Address" "Data Length"

Start Address : "0x0000 0040 0000"
Lentgh : "0X0000 0140 0000"

4-Uncheck 3 option...Select "Rom1"
5-Open "Dump File" in "Main" Window
6-Select "Use Adress as Offset xxxxxx"
7-Press "write"

From : forum.gsmhosting.com

Nokia 2610b​ rm-87 dead after convort to 2610 rm-86 solved

ជួយផង nokia 2610b rm-87 បានរាយ rm-86 v7.11 ហើយក៏ស្លាប់តែម្តង 
បានធ្វើ:
-eras - flash ជាមួយ HWK មិនសំរេច
-eras - flash ជាមួយ MxBox មិនសំរេច
-eras - flash ជាមួយ ATF ជាមួយ V7.04 មិនសំរេចទៀត
តើមានវិធីផ្សេងទេជួយផង ???

ImageFile:C:\Program Files\Nokia\Phoenix\Products\RH-87\2610b 7.04\rh86_87__07.04.mcusw
PhoneType : DCT4
Algorithm : DCT4 ALGORITHM
Supported Hardwares :
> 3040
Secondary Sending Speed : 100000Hz
Algorithm Sending Speed : 6500000Hz
Program Sending Speed : 6500000Hz
Message Reading Speed : 51000Hz
Number of Blocks : 554
Entry Point: 0x00D6
Is128k: True
Boot Check, Please wait...
MCUID Response
-------------------------------------
MessageID : 92
msbUPP_ID : 31
lsbUPP_ID : 68
-------------------------------------
Boot OK

Boot File: C:\AdvanceBox Turbo Flasher\Nokia\DCT4_Loader\u3_2nd.fia
DataLen : 000009D8
Secondary Loader Sent...
Boot OK!
MCU_CONFIGURATION_RESPONSE_DCT4_MUL3
DCT4 Mess 9F MUL3 Mess 9F
TransMode : 03
NumFlash : 02
DevAddr0 : 01
ManuId0 : 0020 - ST
DevId0 : 8804 - Type not in database
ExtId0 : 0000
RevId0 : 7321
SectorSize0: 11
Reserved0 : 00
DevAddr1 : 02
ManuId1 : 0000 - Flash
DevId1 : 0001 - not used
ExtId1 : 0000
RevId1 : 0000
SectorSize1: 00
Reserved1 : 00
ExtBUSC : FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
CheckSum : B5
ReceiveConfigurationResponse_DCT4 - FLS1_NO_ERROR
SearchForBootstrap_DCT4 : No Error
Algo Match File : C:\AdvanceBox Turbo Flasher\Nokia\DCT4_Loader\u3_intel.fia
ALGO SENT..
Perform AUTHENTICATION..
MSID: 848747CD783EFE4BE1F30E117D
DecodedMSID: 84F145BAE900560F69A8000000
EncodedFAID: 3F342B4B26F0904221DEEC49
Authentication : SUCCESSFULL
Erasing address:
>> 01000000 : 0101FFFF
BB_PROGRAMMING_STATUS_REQUEST : 04 FF
ProgrammingStatus_DCT4 : No Error - 0 (0x00)

>> 01020000 : 018DFFFF
BB_PROGRAMMING_STATUS_REQUEST : 04 FF
ProgrammingStatus_DCT4 : No Error - 0 (0x00)

>> 01EE0000 : 01FDFFFF
BB_PROGRAMMING_STATUS_REQUEST : 04 FF
ProgrammingStatus_DCT4 : No Error - 0 (0x00)

Erasing Done
Flashing ImageFile
ContinueFlash_DCT4 Complete
Write Time Elapse : 00:00:57
FLASH Mode Set to : PHONEMODE_FLASHBUS
ProgrammingStatus_DCT4
BB_PROGRAMMING_STATUS_REQUEST : 04 FF -- Progamming status
First Byte OK
Second Byte OK
BB_PERM_DATA_RESTORE_REQ : 18 FF
BB_RESTART : 07 FF
MCURestart : SUCCESS
Making delay between files for 6000ms
ImageFile:C:\Program Files\Nokia\Phoenix\Products\RH-87\2610b 7.04\rh86_87__07.04.ppm_ej
PhoneType : DCT4
Algorithm : DCT4 ALGORITHM
Supported Hardwares :
> 3040
Secondary Sending Speed : 100000Hz
Algorithm Sending Speed : 6500000Hz
Program Sending Speed : 3250000Hz
Message Reading Speed : 51000Hz
Number of Blocks : 104
Entry Point: 0x00CA
Is128k: True
Boot Check, Please wait...
MCUID Response
-------------------------------------
MessageID : 92
msbUPP_ID : 31
lsbUPP_ID : 68
-------------------------------------
Boot OK

Boot File: C:\AdvanceBox Turbo Flasher\Nokia\DCT4_Loader\u3_2nd.fia
DataLen : 000009D8
Secondary Loader Sent...
Boot OK!
MCU_CONFIGURATION_RESPONSE_DCT4_MUL3
DCT4 Mess 9F MUL3 Mess 9F
TransMode : 03
NumFlash : 02
DevAddr0 : 01
ManuId0 : 0020 - ST
DevId0 : 8804 - Type not in database
ExtId0 : 0000
RevId0 : 7321
SectorSize0: 11
Reserved0 : 00
DevAddr1 : 02
ManuId1 : 0000 - Flash
DevId1 : 0001 - not used
ExtId1 : 0000
RevId1 : 0000
SectorSize1: 00
Reserved1 : 00
ExtBUSC : AD 7E B6 1A 1B BE 0B E2 7D 58 6B E4 DB EE 65 14
CheckSum : 7E
ReceiveConfigurationResponse_DCT4 - FLS1_NO_ERROR
SearchForBootstrap_DCT4 : No Error
Algo Match File : C:\AdvanceBox Turbo Flasher\Nokia\DCT4_Loader\u3_intel.fia
ALGO SENT..
Perform AUTHENTICATION..
MSID: 84F6091F9D0DDB3D1EF2336455
DecodedMSID: 843E4EBAE900560F69A8000000
EncodedFAID: 7776DAA6BC836AF24FD55DA8
Authentication : SUCCESSFULL
Erasing address:
>> 018E0000 : 01B7FFFF
BB_PROGRAMMING_STATUS_REQUEST : 04 FF
ProgrammingStatus_DCT4 : No Error - 0 (0x00)

Erasing Done
Flashing ImageFile
ContinueFlash_DCT4 Complete
Write Time Elapse : 00:00:11
FLASH Mode Set to : PHONEMODE_FLASHBUS
ProgrammingStatus_DCT4
BB_PROGRAMMING_STATUS_REQUEST : 04 FF -- Progamming status
First Byte OK
Second Byte OK
BB_PERM_DATA_RESTORE_REQ : 18 FF
BB_RESTART : 07 FF
MCURestart : SUCCESS
Making delay between files for 6000ms
ImageFile:C:\Program Files\Nokia\Phoenix\Products\RH-87\2610b 7.04\rh86_87__07.04.image_ej
PhoneType : DCT4
Algorithm : DCT4 ALGORITHM
Supported Hardwares :
> 3040
Secondary Sending Speed : 100000Hz
Algorithm Sending Speed : 6500000Hz
Program Sending Speed : 6500000Hz
Message Reading Speed : 51000Hz
Number of Blocks : 76
Entry Point: 0x00CD
Is128k: False
C:\Program Files\Nokia\Phoenix\Products\RH-87\2610b 7.04\rh86_87__07.04.image_ej_128k
PhoneType : DCT4
Algorithm : DCT4 ALGORITHM
Supported Hardwares :
> 3040
Secondary Sending Speed : 100000Hz
Algorithm Sending Speed : 6500000Hz
Program Sending Speed : 6500000Hz
Message Reading Speed : 51000Hz
Number of Blocks : 80
Entry Point: 0x00CD
Is128k: False
Boot Check, Please wait...
MCUID Response
-------------------------------------
MessageID : 92
msbUPP_ID : 31
lsbUPP_ID : 68
-------------------------------------
Boot OK

Boot File: C:\AdvanceBox Turbo Flasher\Nokia\DCT4_Loader\u3_2nd.fia
DataLen : 000009D8
Secondary Loader Sent...
Boot OK!
MCU_CONFIGURATION_RESPONSE_DCT4_MUL3
DCT4 Mess 9F MUL3 Mess 9F
TransMode : 03
NumFlash : 02
DevAddr0 : 01
ManuId0 : 0020 - ST
DevId0 : 8804 - Type not in database
ExtId0 : 0000
RevId0 : 7321
SectorSize0: 11
Reserved0 : 00
DevAddr1 : 02
ManuId1 : 0000 - Flash
DevId1 : 0001 - not used
ExtId1 : 0000
RevId1 : 0000
SectorSize1: 00
Reserved1 : 00
ExtBUSC : AD 7E B6 1A 1B BE 0B E2 7D 58 6B E4 DB EE 65 14
CheckSum : 7E
ReceiveConfigurationResponse_DCT4 - FLS1_NO_ERROR
SearchForBootstrap_DCT4 : No Error
Algo Match File : C:\AdvanceBox Turbo Flasher\Nokia\DCT4_Loader\u3_intel.fia
ALGO SENT..
Perform AUTHENTICATION..
MSID: 8495D010CDB694CB119A71121C
DecodedMSID: 84D26EBAF100560F69AA000610
EncodedFAID: FE33322E92B24B92276A244E
Authentication : SUCCESSFULL
Erasing address:
>> 01B80000 : 01EDFFFF
BB_PROGRAMMING_STATUS_REQUEST : 04 FF
ProgrammingStatus_DCT4 : No Error - 0 (0x00)

Erasing Done
Flashing ImageFile
ContinueFlash_DCT4 Complete
Write Time Elapse : 00:00:08
FLASH Mode Set to : PHONEMODE_FLASHBUS
ProgrammingStatus_DCT4
BB_PROGRAMMING_STATUS_REQUEST : 04 FF -- Progamming status
First Byte OK
Second Byte OK
BB_PERM_DATA_RESTORE_REQ : 18 FF
BB_RESTART : 07 FF
MCURestart : SUCCESS
Time Elapse : 00:04:29
____________________________________________________________________

គ្រាន់តែជាមួយ Firmware RH-87_ATT_704a.  ជាការស្រេច 100%
____________________________________________________________________

MCU File: rh87__07.04a.mcusw
1st Boot: Ok, DCT4, UPP: 3168 [Rh-87] [2.2.0.3]
2nd Boot: u3_2nd.fia, Ver: 4.79.0
Fl0: 0x01000000-0x01FFFFFF,00208804,St M36L0R7040U
Algorithm: u3_intel.fia, Ver: 4.80.0
Algorithm Ok, MSID: 846BE89FBF118E2DCABDE30730
Decoded MSID: 57B5BAE9-00560F69-A9000000
Encoded FAID: C2E393D2-C95C877A-11101292
IMAGE: rh87__07.04a.mcusw
Area1: 0x01000000-0x0101FFFF Erased, Time: 00:01
Area2: 0x01020000-0x018DFFFF Erased, Time: 01:35
Area3: 0x01EE0000-0x01FDFFFF Erased, Time: 00:10
MCU Flashing Completed, Time: 01:36
CNT File: rh87__07.04a.image_mcr_att_u_v1
Chip SECTOR_SIZE: 128k, File FAT_SECTOR_SIZE: 64k
Warning, Must be Used 128Kb Sector_Size CNT File
128K Image Saved as: rh87__07.04a.image_mcr_att_u_v1_128
IMAGE: rh87__07.04a.image_mcr_att_u_v1
Area1: 0x01B80000-0x01EDFFFF Erased, Time: 00:36
CNT Flashing Completed, Time: 00:24
Running: Nokia File Server
CNT Extract Warning, Res: 0, CNT Area not Empty
Contents Package Extracting Ok, Time: 00:07
PPM File: rh87__07.04a.ppm_mcr
1st Boot: Ok, DCT4, UPP: 3168 [Rh-87] [2.2.0.3]
2nd Boot: u3_2nd.fia, Ver: 4.79.0
Fl0: 0x01000000-0x01FFFFFF,00208804,St M36L0R7040U
Algorithm: u3_intel.fia, Ver: 4.80.0
Algorithm Ok, MSID: 84F6091F9D0DDB3D1EF2336455
Decoded MSID: 3E4EBAE9-00560F69-A8000000
Encoded FAID: 7776DAA6-BC836AF2-4FD55DA8
IMAGE: rh87__07.04a.ppm_mcr
Area1: 0x018E0000-0x01B7FFFF Erased, Time: 00:28
PPM Flashing Completed, Time: 00:18
Flashing Completed, Rebooting Mobile

នេះជាដំណោះស្រាយដែលខ្ញុំធ្លាប់បានជួយ